FDA & Process Tubing
fda---process-tubing
Almost totally inert, FLUOROPOLYMER tubing can be used with virtually all industrial solvents, chemicals, and corrosive materials, even at elevated temperatures. It does, however, react with fluorine, molten sodium hydroxide, and molten alkali metals.
FLUOROPOLYMER tubing can be steam or chemically sterilized in-line with any industrial cleaner, solvent, or sterilizing method.
FLUOROPOLYMER’s non-stick property allows transport of viscous, sticky materials without line clogging. It also offers outstanding aging resistance.
PTFE’s translucent white color will vary naturally from lot to lot, however the quality and physical properties do not change. FEP and PFA are clearer and can be heat sealed and heat bonded.
Permanent color striping, etching, and longer-than-listed lengths are available through minimum order. Polyethylene-jacketed, thin-wall fluoropolymer tubing, for low-cost purity, is also available through minimum order.
What is it?
PTFE (Polytetrafluoroethylene) resin is supplied in powdered form, which is mixed, preformed, and extruded into a paste, and then finally tubing. It is translucent white in color.
FEP (Fluorinated Ethylene Propylene) resin is pelletized for its hot-melt extrusion process and is a clear tubing.
PFA (Perfluoroalkoxy) resin is also a pelletized product which is hot melt extruded. It, too, is clear. /Asset/a4199.jpg
Almost totally inert. COILTEF can be used with all industrial solvents, chemicals, and corrosive materials even at elevated temperatures. It does, however, react with fluorine, molten sodium hydroxide, and molten alkali metals.
Fluoropolymer's non-stick property allows transport of viscous, sticky material without line clogging. It also offers outstanding aging resistance.
COILTEF is manufactured through a fabrication process which heat sets the coils. The coils should remain stable up to 200ºF. At higher temperatures the coils will begin to relax and lose their set. If the application involves elevated temperatures, in-house testing is recommended.
COILTEF may be steam or chemically sterilized in-line with any industrial cleaner, solvent, or sterilizing method. Care should be taken with steam sterilization to prevent coil relaxation. Testing is recommended.
COILTEF can be manufactured from 0.085" to 1/2" tubing I.D. The coil diameter can be produced from 3/4" O.D. to 4" O.D.
PFA-formulated COILTEF is available by special order. /Asset/a4201.jpg
Vacuum Service: 29.9 in./Hg.
Bend Diameter: 1/2 of tubing I.D.
Extension/Compression Length Ratio: 2 to 1
Optimal flow is achieved and turbulence minimized by passing fluids through CORRTEF in the direction of the corrugation angles (as illustrated).
CORRTEF is heat sealable, and the cuffs (straight ends) are made to accept standard barbed fittings. The end may be flared or expanded to permit shrink-tight connections.
CORRTEF is manufactured in an industrial atmosphere and should be properly sterilized for dean-flow applications. For optimal cleaning of CORRTEF, the tube should be stretched to its maximum length and held vertically (direction of flow: down). Due to the annular corrugations, it may not be possible to remove all traces of particulate from CORRTEF, even under optimal cleaning conditions. /Asset/a4202.jpg
CONTEF's helical construction aids in self cleaning when flushed with standard cleaning fluids.
The cuffs (straight ends) are made to accept standard barbed fittings. Hose assemblies made to your specifications are available.
PTFE's color will vary naturally from lot to lot, but the quality and physical properties do not change.
FEP CONTEF for longer continuous lengths - up to 500 ft. - is available through custom order.
CONTEF Without Wire:
Vacuum Service: 29.9 in./Hg at 70ºF.
Convolutions are molded into the tubing and will not cold flow into a straight wall under normal conditions.
CONTEF With Wire:
Vacuum Service: 29.9 in./Hg at 70ºF.
For high vacuum applications, CONTEF can be produced with wire on the I.D. /Asset/a4206.jpg
ZELITE conforms to the applicable regulations of the FDA for use of articles intended for contact with food. The increased tensile strength of ZELITE Linear Low Density, over that of a low density polyethylene, enhances its resistance to splitting during use.
FEP-lined polyethylene, offering superior purity at a very reasonable cost, is available through minimum order. Medium-high and ultra-high density polyethylene material is available through minimum order. Medium-high and ultra high density polyethylene material is available through minimum order. /Asset/a4209.jpg
SUPRENE offers excellent flex fatigue resistance and good tear resistance, making it an ideal choice for peristaltic pump applications. The FDA material is suitable for a variety of clean uses and is autoclavable to ensure cleanliness.
Black industrial SUPRENE offers good resistance to U.V., ozone, chemicals, and other fluids. It will also handle applications where oil may splash onto the tubing and is well suited for outdoor use. /Asset/a4197.jpg
PE-LINED EVA (Ethylene Vinyl Acetate) tubing is designed for use where high purity is required. It also offers excellent chemical resistance and non-toxicity, while maintaining good flexibility. A co-extruded product, PE-LINED EVA is made of a low density polyethylene liner with an EVA outer jacket. It is manufactured in a patented process (Patent No, 4061461) to ensure the highest bond quality possible.
PE-LINED EVA tubing meets Class VI requirements and is suitable for use in poultry and meat processing. PE-LINED EVA also meets or exceeds standards in National Formulary, Vol. 14 for containers for injectable (plastics).
This product is an excellent substitute for PTFE, at working temperatures below 100ºF, with cost savings of 50% or more. For working temperatures up to 180ºF and greater stress resistance, ask about irradiated PE-LINED EVA tubing. /Asset/a4210.jpg
PROLITE is a high-crystalline, polypropylene copolymer tubing. The compound used in its manufacture is NSF-61 listed and meets FDA requirements for food contact surfaces. It also meets the UL 94 HB burn rating.
PROLITE is frequently used in food processing and other industries for clean applications. It is a naturally white, semi-rigid product offering limited ability to bend. Since it is weldable, PROLITE may be joined directly, although it is typically joined by means of a push-to-connect fitting such as Newloc®.
Polypropylene is the lightest of all thermoplastic materials. It offers high strength-to-weight ratio, low surface friction, and excellent resistance to corrosion.
Based on its physical properties, PROLITE may be applied as a reasonably-priced alternative to fluoropolymer tubing in many applications. /Asset/a4211.jpg
HYTREL-LINED PVC TUBING is designed to offer the flexibility and durability of PVC tubing with a liner of inert. DuPont Dow Elastomers' Hytrel for additional resistance to oils, high temperatures, and gas permeability. A patented process molecularly bonds liner and jacket to make a virtually inseparable product. This cost- saving co-extrusion permits HYTREL-LINED PVC to be substituted for conventional reinforced PVC hose in many applications.
The Hytrel polyester core offers internal resistance to chemical attack, abrasion, and contamination, along with a high degree of resistivity to adherence of particulates, making HYTREL LINED PVC exceptionally suited for use in air sampling applications.
HYTREL-LINED PVC TUBING'S black PVC jacket offers excellent resistance to abrasion and oils, as well as U.V. The pliable PVC also provides a degree of shock resistance and insulates the tubing from electronic interference.
HYTREL-LINED PVC TUBING is made of FDA- sanctioned ingredients for use with food contact surfaces. The tubing withstands repeated autoclaving with no separation of layers. /Asset/a4213.jpg
AdvantaFlex addresses the need for a flexible, translucent, sterilizable, moldable, heat sealable, and weldable biopharmaceutical tubing for fluid processing. AdvantaFlex maintains its physical properties following sterilization processes, resists kinking, remains translucent for visible product flow, and does not become gummy. Additionally, the unique properties of AdvantaFlex help it outperform similar tubing in peristaltic pumps.
Key Features
SILCON MED-X tubing is made under strict accordance with FDA Good Manufacturing Practices (GMP) and conforms to the biocompatibility requirements of USP Class VI.
SILCON MED-X’s surface properties resist sticking and encrustation and will not support bacteria growth. The tubing is soft, pliable, and contains no plasticizers which could leach out, causing flow contamination or tube hardening.
Other sizes and 60A durometer material are also available.
SILCON MED-X is not recommended for implantable or in-body uses.
Care is recommended in the selection and application of fittings and clamps as sharp barbed fittings or unlined metal clamps could tear into the wall.
SILCON MED-X is supplied in individual, heat-sealed polybags and should be sterilized prior to use. /Asset/a4195.jpg
Fluoropolymer Tubing (PTFE, FEP & PFA)
(91)- Chemically inert; low permeability
- Manufactured from FDA-sanctioned ingredients for use with food contact surfaces
- Lowest coefficient of friction of any solid material
- Widest service temperature of any plastic tubing (-275ºF to 500ºF)
- Excellent electrical and weathering properties; non-flammable
- Made without plasticizer which can leach into critical streams
- Ultra-high-purity grades available for the semiconductor industry.
Almost totally inert, FLUOROPOLYMER tubing can be used with virtually all industrial solvents, chemicals, and corrosive materials, even at elevated temperatures. It does, however, react with fluorine, molten sodium hydroxide, and molten alkali metals.
FLUOROPOLYMER tubing can be steam or chemically sterilized in-line with any industrial cleaner, solvent, or sterilizing method.
FLUOROPOLYMER’s non-stick property allows transport of viscous, sticky materials without line clogging. It also offers outstanding aging resistance.
PTFE’s translucent white color will vary naturally from lot to lot, however the quality and physical properties do not change. FEP and PFA are clearer and can be heat sealed and heat bonded.
Permanent color striping, etching, and longer-than-listed lengths are available through minimum order. Polyethylene-jacketed, thin-wall fluoropolymer tubing, for low-cost purity, is also available through minimum order.
What is it?
PTFE (Polytetrafluoroethylene) resin is supplied in powdered form, which is mixed, preformed, and extruded into a paste, and then finally tubing. It is translucent white in color.
FEP (Fluorinated Ethylene Propylene) resin is pelletized for its hot-melt extrusion process and is a clear tubing.
PFA (Perfluoroalkoxy) resin is also a pelletized product which is hot melt extruded. It, too, is clear. /Asset/a4199.jpg
Coiltef® Coiled FEP Tubing
(5)- Made of chemically inert clear FEP
- Manufactured from FDA-sanctioned ingredients
- Heat set into a retractable coil; excellent recoil memory
- Offers all the chemical and electrical insulation properties of standard FEP fluoropolymer tubing
- Allows flexibility to otherwise semi-rigid fluoropolymer tubing
- Made to order or stocked sizes available
Almost totally inert. COILTEF can be used with all industrial solvents, chemicals, and corrosive materials even at elevated temperatures. It does, however, react with fluorine, molten sodium hydroxide, and molten alkali metals.
Fluoropolymer's non-stick property allows transport of viscous, sticky material without line clogging. It also offers outstanding aging resistance.
COILTEF is manufactured through a fabrication process which heat sets the coils. The coils should remain stable up to 200ºF. At higher temperatures the coils will begin to relax and lose their set. If the application involves elevated temperatures, in-house testing is recommended.
COILTEF may be steam or chemically sterilized in-line with any industrial cleaner, solvent, or sterilizing method. Care should be taken with steam sterilization to prevent coil relaxation. Testing is recommended.
COILTEF can be manufactured from 0.085" to 1/2" tubing I.D. The coil diameter can be produced from 3/4" O.D. to 4" O.D.
PFA-formulated COILTEF is available by special order. /Asset/a4201.jpg
Corrtef® Corrugated FEP Tubing
(10)- Made from FEP fluoropolymer tubing
- Corrugations allow a nearly zero bend radius - easily flexed
- Can be extended or compressed without affecting the tube's I.D.
- Made from FDA-sanctioned ingredients
- Made without plasticizers which can leach into critical streams
- Has all the chemical and electrical properties of straight-walled FEP tubing
- May be over braided with Kevlar® for higher pressures. (Over braiding with Kevlar will permit a minimum increase of six times the listed pressures. Kevlar over braiding is available for sizes up to 7/8" I.D.)
Vacuum Service: 29.9 in./Hg.
Bend Diameter: 1/2 of tubing I.D.
Extension/Compression Length Ratio: 2 to 1
Optimal flow is achieved and turbulence minimized by passing fluids through CORRTEF in the direction of the corrugation angles (as illustrated).
CORRTEF is heat sealable, and the cuffs (straight ends) are made to accept standard barbed fittings. The end may be flared or expanded to permit shrink-tight connections.
CORRTEF is manufactured in an industrial atmosphere and should be properly sterilized for dean-flow applications. For optimal cleaning of CORRTEF, the tube should be stretched to its maximum length and held vertically (direction of flow: down). Due to the annular corrugations, it may not be possible to remove all traces of particulate from CORRTEF, even under optimal cleaning conditions. /Asset/a4202.jpg
Contef® Convoluted PTFE Tubing
(21)- Translucent PTFE tubing offers excellent chemical and electrical properties
- Available from stock with or without a stainless steel wire encircling the O.D. Wire coil provides increased pressure capability and aids in electrical grounding
- Easily flexed - spiral construction allows far greater flexibility than straight wall tubing
- Spiral construction also allows for easier cleaning
- Made from FDA-sanctioned ingredients
- Available to AMS-T-81914/1 (without wire only)
(CONTEF with AMS (Aerospace Material Specifications) is available without wire only and is not stocked)
CONTEF's helical construction aids in self cleaning when flushed with standard cleaning fluids.
The cuffs (straight ends) are made to accept standard barbed fittings. Hose assemblies made to your specifications are available.
PTFE's color will vary naturally from lot to lot, but the quality and physical properties do not change.
FEP CONTEF for longer continuous lengths - up to 500 ft. - is available through custom order.
CONTEF Without Wire:
Vacuum Service: 29.9 in./Hg at 70ºF.
Convolutions are molded into the tubing and will not cold flow into a straight wall under normal conditions.
CONTEF With Wire:
Vacuum Service: 29.9 in./Hg at 70ºF.
For high vacuum applications, CONTEF can be produced with wire on the I.D. /Asset/a4206.jpg
Zelite™ Linear Low Density Polyethylene Tubing
(30)- Made from non-toxic ingredients conforming to FDA standards
- Does not impart a taste or odor to critical streams
- Flexible, lightweight, durable
- Translucent natural or opaque colors
- Made from 100% virgin grade raw materials
- Good dielectric properties
- Offers enhanced resistance to stress cracking
- Chemically inert; forms a good barrier to gases, vapors, and moisture
ZELITE conforms to the applicable regulations of the FDA for use of articles intended for contact with food. The increased tensile strength of ZELITE Linear Low Density, over that of a low density polyethylene, enhances its resistance to splitting during use.
FEP-lined polyethylene, offering superior purity at a very reasonable cost, is available through minimum order. Medium-high and ultra-high density polyethylene material is available through minimum order. Medium-high and ultra high density polyethylene material is available through minimum order. /Asset/a4209.jpg
Suprene® Thermoplastic Rubber (TPR) Tubing
(30)- Made of first-quality, polypropylene-based, thermoplastic rubber (TPR)
- Outstanding compression characteristics and toughness for peristaltic pump uses
- Available in both FDA and industrial grades
- Natural 80A material is listed by the National Sanitation Foundation (NSF-51)
(Other durometers with an NSF listing are available as a custom item) - Made to Good Manufacturing Practices (GMP)
SUPRENE offers excellent flex fatigue resistance and good tear resistance, making it an ideal choice for peristaltic pump applications. The FDA material is suitable for a variety of clean uses and is autoclavable to ensure cleanliness.
Black industrial SUPRENE offers good resistance to U.V., ozone, chemicals, and other fluids. It will also handle applications where oil may splash onto the tubing and is well suited for outdoor use. /Asset/a4197.jpg
Polyethylene-Lined EVA Co-Extruded Tubing
(9)- Made from Class VI, FDA-sanctioned ingredients for use with food and beverage contact surfaces
- Natural translucent color for visual contact with the flow
- Remains flexible at temperatures from -29ºF to 160ºF
- Non-toxic; odorless, tasteless, and inert
- Remains pliable even after extended contact with alcohol
- Good weatherability properties - resists U.V., ozone, gases, and moisture
- Low friction coefficient and excellent chemical resistance allows easy passage of solids, alcohols, acids, caustics and solvents.
PE-LINED EVA (Ethylene Vinyl Acetate) tubing is designed for use where high purity is required. It also offers excellent chemical resistance and non-toxicity, while maintaining good flexibility. A co-extruded product, PE-LINED EVA is made of a low density polyethylene liner with an EVA outer jacket. It is manufactured in a patented process (Patent No, 4061461) to ensure the highest bond quality possible.
PE-LINED EVA tubing meets Class VI requirements and is suitable for use in poultry and meat processing. PE-LINED EVA also meets or exceeds standards in National Formulary, Vol. 14 for containers for injectable (plastics).
This product is an excellent substitute for PTFE, at working temperatures below 100ºF, with cost savings of 50% or more. For working temperatures up to 180ºF and greater stress resistance, ask about irradiated PE-LINED EVA tubing. /Asset/a4210.jpg
Prolite® Polypropylene Tubing
(9)- Made of NSF-61 listed, virgin Polypropylene copolymer conforming to FDA requirements for food contact surfaces
- Extremely lightweight, thermoformable, and weldable
- Very low moisture absorption
- High dielectric strength
- Meets UL94 HB burn rating
- Excellent chemical resistance
- Naturally white in color.
PROLITE is a high-crystalline, polypropylene copolymer tubing. The compound used in its manufacture is NSF-61 listed and meets FDA requirements for food contact surfaces. It also meets the UL 94 HB burn rating.
PROLITE is frequently used in food processing and other industries for clean applications. It is a naturally white, semi-rigid product offering limited ability to bend. Since it is weldable, PROLITE may be joined directly, although it is typically joined by means of a push-to-connect fitting such as Newloc®.
Polypropylene is the lightest of all thermoplastic materials. It offers high strength-to-weight ratio, low surface friction, and excellent resistance to corrosion.
Based on its physical properties, PROLITE may be applied as a reasonably-priced alternative to fluoropolymer tubing in many applications. /Asset/a4211.jpg
Hytrel®-Lined PVC Co-Extruded Tubing
(3)- Made from FDA-sanctioned ingredients
- Hytrel core resists high temperatures and oils, making it ideal for hot beverage vending machine applications
- Low permeability to refrigerant gases and hydrocarbons
- Odorless, tasteless, and inert
- Good weathering properties - resists U.V., ozone, gases, moisture, and temperatures
- Low adherence of particulates - ideal for air sampling applications
- Withstands repeated autoclaving
HYTREL-LINED PVC TUBING is designed to offer the flexibility and durability of PVC tubing with a liner of inert. DuPont Dow Elastomers' Hytrel for additional resistance to oils, high temperatures, and gas permeability. A patented process molecularly bonds liner and jacket to make a virtually inseparable product. This cost- saving co-extrusion permits HYTREL-LINED PVC to be substituted for conventional reinforced PVC hose in many applications.
The Hytrel polyester core offers internal resistance to chemical attack, abrasion, and contamination, along with a high degree of resistivity to adherence of particulates, making HYTREL LINED PVC exceptionally suited for use in air sampling applications.
HYTREL-LINED PVC TUBING'S black PVC jacket offers excellent resistance to abrasion and oils, as well as U.V. The pliable PVC also provides a degree of shock resistance and insulates the tubing from electronic interference.
HYTREL-LINED PVC TUBING is made of FDA- sanctioned ingredients for use with food contact surfaces. The tubing withstands repeated autoclaving with no separation of layers. /Asset/a4213.jpg
Advantaflex Biopharmaceutical Grade TPE Tubing
(15) A new formulation of TPE (thermoplastic elastomer) tubing has been developed for fluid transfer in the biopharmaceutical industry: AdvantaFlex.AdvantaFlex addresses the need for a flexible, translucent, sterilizable, moldable, heat sealable, and weldable biopharmaceutical tubing for fluid processing. AdvantaFlex maintains its physical properties following sterilization processes, resists kinking, remains translucent for visible product flow, and does not become gummy. Additionally, the unique properties of AdvantaFlex help it outperform similar tubing in peristaltic pumps.
Key Features
- Excellent life in peristaltic pumps
- Sterile weldable and heat sealable
- Now available as leak - proof molded connections and tubing
- Made from FDA-approved ingredients
- Excellent low absorption and adsorption characteristics as compared to silicone
- Meets various ISO and USP standards, including Class VI
- Meets European Pharmacopoeia 3.2.2.1 standards
- Low permeability as compared to silicone
- Certified free of silicone oils and animal-derived ingredients
- Smooth interior for excellent flow and performance
- Sterilizable by gamma radiation or autoclave
- Translucent for fluid flow visibility
- Excellent tubing component for single-use systems
- Sizes from 1/8" (0.125) through 1" (1.000) I.D.
- Custom lengths, sizes, and packaging available
- Sealed in polybags at manufacture for cleanliness
- Documented quality control; lot traceable with identification on polybags
- Single resin validation - no need to graft to other tubing materials like silicone for media filling and sampling applications that involves peristaltic pumps; helps eliminate operator errors
- Chemical Characterization of Materials per ISO - "Extractables" test portfolio available
SILCON®
(35)- Made from FDA-sanctioned ingredients
- Able to resist extreme temperature variation: -100°F to 500°F
- Translucent natural color for visual contact with the flow
- Resilient, stretchable, and resistant to compression set
- Odorless, tasteless, and inert
- Good electrical and weatherability properties - resists U.V., ozone, gases, and moisture
- Listed by the National Sanitation Foundation (NSF 51)
Silcon® Med-X Platinum-Cured Medical Grade Silicon Tubing
(19)- Silicone elastomer meets USP Class VI requirements
- Manufactured under strict Good Manufacturing Practices (GMP) in a controlled environment
- Platinum cured for the highest degree of purity (least extractables)
- Reusable - will withstand repeated sterilization (If exposed to repeated steam sterilization or long-term high temperature or pressure, silicone will eventually relax and become gummy. It should then be replaced.)
- Nonreactive to body tissues and fluids
- Applications include pharmaceutical, biomedical, health and beauty, food, and beverage handling
SILCON MED-X tubing is made under strict accordance with FDA Good Manufacturing Practices (GMP) and conforms to the biocompatibility requirements of USP Class VI.
SILCON MED-X’s surface properties resist sticking and encrustation and will not support bacteria growth. The tubing is soft, pliable, and contains no plasticizers which could leach out, causing flow contamination or tube hardening.
Other sizes and 60A durometer material are also available.
SILCON MED-X is not recommended for implantable or in-body uses.
Care is recommended in the selection and application of fittings and clamps as sharp barbed fittings or unlined metal clamps could tear into the wall.
SILCON MED-X is supplied in individual, heat-sealed polybags and should be sterilized prior to use. /Asset/a4195.jpg
SILBRADE® Braid Reinforced Silicone Hose
(9)- Open mesh polyester braiding incorporated within the wall of silicone silicone tubing
- Made from FDA-sanctioned ingredients
- Translucent natural color for visual contact with the flow
- Able to resist extreme temperature variation: -80ºF to 350ºF
- Odorless, tasteless, and inert
- Excellent weatherability properties -- resists U.V., ozone, gases, moisture, and extreme temperatures
- Offers far higher pressure capabilities than similarly-sized unreinforced silicone tubing
- Listed by the National Sanitation Foundation (NSF 51)
SILBRADE® MEDICAL
(7)- Open mesh polyester braiding incorporated within the wall of silicone tubing
- Silicone elastomer meets USP Class VI and NSF-51 requirements
- Translucent natural color for visual contact with the flow
- Able to resist extreme temperature variation: -80ºF to 350ºF
- Odorless, tasteless, and inert
- All ingredients are non-toxic and FDA-sanctioned for use with food contact surfaces
- Manufactured under strict Good Manufacturing Procedures in a controlled environment
SILCON® MEDICAL
(26)- Silicone elastomer meets USP Class VI and NSF-51 requirements
- Manufactured under strict Good Manufacturing Procedures in a controlled environment Reusable -- will withstand repeated sterilization
- Nonreactive to body tissues and fluids
- Translucent natural color for visual contact with the flow
- Odorless, tasteless, and inert
- All ingredients are non-toxic and FDA-sanctioned for use with food contact surfaces
- May be used in peristaltic pumps
APSPG Pump Grade Silicone Tubing
(10)Class VI, platinum-cured silicone elastomer comprises AdvantaPure’s new peristaltic pump grade silicone tubing. Ideally suited for pharmaceutical, biotech, and laboratory environments, APSPG is specially formulated to withstand repeated compression and release for consistent, dependable performance – far outlasts standard silicone tubing.
APSPG Pump Grade Silicone Tubing is not intended for implantation, continuous steam applications, or elevated pressure levels.
Key Features
- Special formulation promotes long life in pumps
- Extremely flexible and resilient; hardness value of 50 Shore A
- Outstanding compression characteristics
- Smooth surfaces offer uniform fluid flow, resistance to bacteria build-up, and consistent pump performance
- APSPG tubing is USP Class VI approved
- Material meets FDA 21 CFR 177.2600
- Low volatile grade suitable for pharmaceutical and biomedical applications
- Maximum operating temperature: 400°F (204.4°C); brittle temperature: less than -100°F (-73.3°C)
- Sterilizable/autoclavable
- Imparts no taste or odor to critical streams
- Translucent for visual contact with the flow
- Stocked in sizes from .031” through .500” I.D.
- Manufactured in a certified HEPA-filtered clean room
- Sealed in polybags at manufacture for cleanliness
- Documented lot traceable with identification on bags and boxes
- Documented quality control
- Custom lengths, sizes, and packaging available upon request
